www.shortscale.org

[taylornutt]

What exactly is the Z Poxy?

I used True Oil on an old 1978 Musicmaster neck that most of the finish was sanded off. Good results. Some of the leftover finish was darker.

Before:


After:


_________________
J Mascis Jazzmaster | Baja Telecaster
AVRI Jaguar | 1967 Fender Coronado II |1977 Mullet-stang | 1973 Fender Bronco

[HNB]

Z Poxy is a two part finishing resin that isn't super picky about being perfectly 50/50 mixed. I use it as a sealer and filler.

[61fury]

Damn you work fast, it usually takes me weeks and months of fretting and procrastination before I can do the slightest of things, like moving from 220 grit to 320. Very nice wood and stain.
I like the traditional tele cup, what I really like is that 45 dollar Rutters press fit cup, I wish some one would knock that off

[HNB]

Work is good because it keeps me from rushing to an extent. Normally I would have done another coat this morning, but I had to get to work so I will only do a coat on one side every 24 hours which is slower than the instructions, but helps make sure the layers are solid before I add more. I am thinking one more coat all around should do it. (Three total.) Then I will gently sand it and start putting tru-oil on. If it doesn't look nice and flat, I will do a fourth coat and even a fifth. I am putting it on very thin to avoid liquid bubbly resin that I would end up having to sand off. For the next coats, I will thin it with denatured alcohol so it will apply flatter.

[HNB]

I sanded the zpoxy filler smooth. There are still little grain areas that aren't totally full, but the tru-oil should do the rest.

IMG_7090 by Hentai No Baka, on Flickr

IMG_7091 by Hentai No Baka, on Flickr

IMG_7092 by Hentai No Baka, on Flickr

First coat of tru-oil. (I put it on kind of thick. I will wait 24 hours before I lightly sand it with fine sandpaper.)

IMG_7095 by Hentai No Baka, on Flickr

My bridge and hotrail pickup came in.

IMG_7093 by Hentai No Baka, on Flickr

[HNB]

So I learned something about tru-oil. (The hard way of course.)

I was putting it on with a plastic glove and spreading it all over. I found out I was putting it on too thick. It was drying with liquid bumpy bits and such. I sanded it flat (which I wouldn't have needed to do if I had done it right) and applied it using a paper towel. Basically I am now rubbing it on instead of putting it on the body and spreading it around. Seems to be working better this way. Dries faster as well.

[HNB]

Finish is drying so I can use 3000 on it to get it satin'ed up.

IMG_7228 by Hentai No Baka, on Flickr

[HNB]

Coming along! Just waiting on parts.

IMG_7276 by Hentai No Baka, on Flickr

IMG_7277 by Hentai No Baka, on Flickr

IMG_7278 by Hentai No Baka, on Flickr

[brainfur]

fuck yeah telecaster
_________________

[HNB]

Here are some updated pictures. I got the neck on, neck pickup added, switch wired, electrostatic cup attached, and pickguard ready for the screws. I am still waiting on the string ferrules for the back of the body, the string tree, toggle switch tip, and pickguard/control plate screws. I used some fun quirky knobs on it. I like that the black plays off of the guard and bridge pickup.

20140630_165052 by Hentai No Baka, on Flickr

20140630_165058 by Hentai No Baka, on Flickr

20140630_165107 by Hentai No Baka, on Flickr

[HNB]

It is basically done now! I installed the back ferrules and the other parts. Just need the switch tip.

20140701_134332 by Hentai No Baka, on Flickr

20140701_134338 by Hentai No Baka, on Flickr

20140701_143535 by Hentai No Baka, on Flickr

20140701_143544 by Hentai No Baka, on Flickr

20140701_143554 by Hentai No Baka, on Flickr

20140701_143612 by Hentai No Baka, on Flickr

20140701_143623 by Hentai No Baka, on Flickr